Electric Drill Water Pump: All You Need To Know

In many situations, you need to get water from one place to another. Doing it manually can be very tiresome, time-consuming, and frustrating at the same time. But you are now living in the 21st century. There must be some machines out there to help you transfer water from the source to the destination. The electric drill water pump is one of the many solutions to your problem.

Pumping and carrying water from and to different places can be done in many ways. Today I will talk about the electric drill water pump. I believe this is the best solution for transferring water on a smaller scale. Electric drill water pumps are comparatively less expensive and easy to operate and can be done by any normal human being.

By profession, I am a water technician and by passion, I am a blogger. In this article, I am going to share all you need to know about electric drill water pumps. I will explain how it works, where it should be used, and how it should be used. I will also suggest some popular electric drill water pumps. Read till the end to get some extra tips and answers to some common questions regarding electric drill water pumps. 

How Does An Electric Drill Water Pump Work? 

The electric drill water pump follows a very simple procedure to transfer water. The round-shaped pump has an impeller in its center. A drilling machine can be attached by its chuck to the impeller of the pump. The pump is designed to be attached to any kind of drilling machine. 

There are two ports of the pump to attach two hosepipes. One for suction of the water and the other for discharging it. When the attached drilling machine is powered on, the impeller of the pump begins to spin at high speed.  

Thus a static and atmospheric pressure is created inside the pump. This low pressure inside the pump forces the water from the source to get sucked into it. 

Then the pressure of the water is increased by the same rotating blades of the pump. The increased pressure of the water pushes them to the outlet pipe. 

A standard electric drill water pump can rotate up to 3,400 times per minute. If you are using a 13 mm hose for the pumping you can shift 28 liters of water each minute. If you are using a 19 mm hose, you can transfer 40 liters of water per minute.

How To Use An Electric Drill Water Pump Properly? (8 Simple Steps)

If electric drill water pumps are not used properly, they can cause fatal accidents. So, before starting to use an electricity-driven drill pump, you should know the following steps:

Step 1- Attach The Impeller Shaft:

First of all, lock the drill chuck of the drilling machine to avoid any accident. Adjust the impeller shaft with the chuck of the drill motor. 

Step 2- Connect Garden Hoses:

Attach the bigger garden hose into the male garden hose inlet of the water pump. Add another smaller hose to the other inlet of the pump. 

Step 3- Get The Hose To Your Source:

Now, get the bigger garden hose into your source water. Make sure the opening of the hose is not obstructed by touching the bottom.

Step 4- Self-Prime The Pump:

For a long life of your pump. Let the built-in self-prime process start. You have to switch on and press the trigger of the drill machine for 30 seconds to finish the process.

Step 5- Take The Output Hose To Your Destination:

Put the smaller garden hose into the container where you want the water to be. Clean the hose properly or it might make the water dirty.

Step 6- Switch On The Drill:

Position the electric drill where it cannot move randomly. If necessary, tie it with the pump. Now Press the trigger of the drill to start the pumping.

Step 7- Be Careful About The Air:

Throughout the whole process of pumping out the water, make sure the inlet hose is never out of the water. If air gets into the hose, it can cause harm to the pump.

Step 8- Finish With A Cleaning:

Thoroughly clean the pump after the pumping is done. Check for any foreign particles inside the pump.

4 Tips On Using An Electric Drill Water Pump:

Now I will share 4 tips about electric drill water pumps. You may find them useful:

Tip 1- Prime Up Your Electric Drill Water Pump Before Each Use:

Prime up the electric drill water pump before using them. It will ensure a longer life for the pump. Carefully follow the user manual of the manufacturer to prime up your pump. Priming your drill water pump will also increase its capacity to transfer fluids.

Tip 2- Do Not Use Drill Pump To transfer Petrol:

The electric drill water pump is not designed to be used for transferring petrol or gasoline. There is a big risk of ignition if you try to do that. Because the drill motor may create some sparks while rotating the impeller of the pump. A single spark will set your pump on fire if they get into touch with the fuel.

Tip 3- Do Not Use Drill Water Pump With A Pressure Washer:

Pressure washers require continuous and consistent water pressure. But a drill water pump may have fluctuations in the flow of the water. If the water pressure is down for some moment, it could cause cavitations in the pressure pump. That is why it is not recommended to use an electric drill water pump with a pressure washer.

Tip 4- Do Not Switch On A Dry Drill Water Pump:

Self-priming drill water pumps need fluid inside them before starting to pump water. Otherwise, its mechanical seal gets damaged. That will make it completely unusable. You must make sure your self-priming drill has enough fluid inside it before turning the drill machine on. 

Commonly Asked Questions About Electric Drill Water Pump:

Who Should Use A Drill Pump?

Any ordinary person with or without any technical knowledge can use a drill pump. It is a very easy-to-use tool for transferring water from one place to another. All he needs is a drill machine, a drip pump, and some common sense. But one should follow the standard procedures to operate a drill water pump.

Where To Use Electric Drill Water Pump?

Pumping water with an electric drill pump sounds easy. But it is not practical to use them on larger scales. Here I am explaining exactly where you should use an electric drill water pump:

  • Water Containers:

Suppose that you have got two 20-liter water gallons. One is full of water and the other is empty. Now you need to get 10 liters of water from the full gallon to the empty gallon. The gallon mouths are so narrow that it is almost impossible to pour water through them without a spill. Also raising and holding a 20-liter full gallon of water is not safe for your back. In this situation, consider using an electric drill water pump. 

  • Fish Tanks:

The big aquarium in your living room represents your love for nature. But only you know how painful it is to change the water of the fish tanks. Using an electric drill water pump, you can easily take out the water from the tank and refill it with fresh water. It will save your living room from getting wet here and there.

  • Jacuzzis:

While installing the jacuzzi at your house, you had no idea how difficult it would be to pour water into it. Now that you are using the relaxation system, you should have an electric drill water pump in your house too. 

  • Small Pools Or Ponds:

Electric drill water pumps are ideal for small pools or ponds. Regular water changing of a swimming pool can be done with ease if you have an electric drill water pump with you. Fish-farming in a pond requires transferring the water to nearby space while catching the fish. Using a drill pump will surely make your job easy.

  • Watering A Garden:

If you have a large garden, watering the garden may seem to be a hard job. You can use an electric drill water pump to make your life easier. Installing a sprinkler with the outlet pipe of the pump will make your garden watered evenly.

When To Use An Electric Drill Water Pump?

There are many situations when an electric drill water pump can be used. They can be used in the agricultural sector for applying liquid pesticides or fertilizers. They are very helpful to water a large garden. You can use a drill water pump at home to change the water of your aquarium or fill up your jacuzzi.

How Does A Self-Priming Drill Pump Work?

A self-priming drill water pump uses the liquid within it to create a vacuum in the suction pipe. To use a drill pump for a longer period, It is very important to make sure it is primed before each use. If your pump is not self-primed, you should prime it up yourself before transferring the water.

Why Should You Prime A Drill Water Pump?

You should prime a drill water pump before using it. Otherwise, it will not function accurately. There will be a lack of pressure and it will not be able to pump up enough water using its suction pipe. Besides, an unprimed drill water pump may get overheated very soon.

How Do You Prime A Drill Pump?

To prime a drill pump, you have to put some water into the impeller of the pump. After making it wet, switch on the attached drill machine. Keep it on for around 30 seconds. You will find the pump to be primed up according to its capacity.

How To Tell If A Drill Water Pump Is Primed Or Not?

You can be sure of whether your electric drill water pump is primed or not by opening one of the relief valves. Before pumping any water, start the pump and wait to see if water starts to run from the relief valve. A primed pump will turn off automatically after the water gets out.

Final Words:

To transfer non-flammable liquids from one place to another, electric drill water pumps are excellent. They are more feasible for small-scale liquid management. Electric drill water pumps are now being largely used in the agricultural sector and contributing to the sustainability of economic growth.

Masud Rana

This is Masud Rana. I run this blog. My Tools Guide is a blog where I share product reviews of different tools. Stay tuned to get more helpful articles!

Recent Posts